The following devices are detected by this driver: acx0: port 0xd000-0xd01f mem 0xf7d30000-0xf7d30fff,0xf7d20000-0xf7d2ffff irq 11 at device 0.0 on cardbus1 acx0: Ethernet address: 00:0a:e2:00:1b:49 acx0: Eeprom Rev 4 Domain ETSI Europe (1-13), Firmware Rev 1.9.8.b acx0@pci4:0:0: class=0x028000 card=0x8403104c chip=0x8400104c rev=0x00 hdr=0x00 vendor = 'Texas Instruments (TI)' device = '802.11b+ 22Mbps Wireless Adapter' class = network acx1: mem 0xf7d60000-0xf7d61fff,0xf7d40000-0xf7d5ffff irq 11 at device 0.0 on cardbus2 acx1: Ethernet address: 00:0d:88:83:3a:d2 acx1: Eeprom Rev 5 Domain ETSI Europe (1-13), Firmware Rev 1.2.1.34 acx1@pci5:0:0: class=0x028000 card=0x3b051186 chip=0x9066104c rev=0x00 hdr=0x00 vendor = 'Texas Instruments (TI)' device = 'TNETW1130(ACX111) 802.11b/g Wireless Cardbus/PCI Adapter' class = network This version tested to work in FreeBSD: 6.1-REL +ifconfig +acxtool 6.2-REL +ifconfig +acxtool 7.0-CURRENT-200710 -ifconfig(broken channel selection) +acxtool contact : darron at kewl org or subcribe to a list here: http://lists.kewl.org/mailman/listinfo/acx Usage: This experimental version of the ACX(4) driver for FreeBSD-6.1+ should work for infrastructure clients, Ad-hoc connections and in a limited form as an access point. In the latter case functionality such as power saving or client to client bridging is not implemented. ifconfig is used to configure the ip address of the adapter which initialises the connection and the application "acxtool" found in the acxtool directory should be compiled to configure attributes such as channel, ssid etc, however ifconfig may perform most of these operations but the feature set at this time is incomplete. Usage: rufus# kldload acx100fw.ko # if you have an acx100 rufus# kldload acx111fw.ko # if you have an acx111 rufus# kldload if_acx.ko # driver for either of the above rufus# kldstat ... 28 1 0xc272e000 d000 acx100fw.ko 29 3 0xc273b000 3000 firmware.ko 30 1 0xc273e000 2b000 acx111fw.ko 31 1 0xc369b000 11000 if_acx.ko ... rufus# acxtool acx0 -M 0 -S kewl9 -C 9 -P 1 -W 0:0xc0dedeadc0dedeadc0dedeadab rufus# ifconfig acx0 inet 10.1.36.140 netmask 255.255.255.128 rufus# ping 10.1.36.129 PING 10.1.36.129 (10.1.36.129): 56 data bytes 64 bytes from 10.1.36.129: icmp_seq=0 ttl=127 time=2.321 ms 64 bytes from 10.1.36.129: icmp_seq=1 ttl=127 time=1.701 ms ^C rufus# ifconfig -v acx0 acx0: flags=843 mtu 1500 inet 10.1.36.140 netmask 0xffffff80 broadcast 10.1.36.255 ether 00:c0:49:ca:79:b4 media: IEEE 802.11 Wireless Ethernet autoselect status: associated ssid kewl9 channel 9 (0) bssid 00:c0:49:cc:64:9c authmode OPEN privacy ON deftxkey 1 txpowmax 63 txpower 63 rufus# acxtool acx0 Mode: ESS SSID: kewl9 Channel: 9 WEP Mode: on WEP Key: 0xc0dedeadc0dedeadc0dedeadab MSDU Lifetime: 4000 ED Threshold: 0x70 Short Retry: 15 Long Retry: 15 CCA Mode: 0x0d Current Antenna: 0x8f Power Level: 63